GSO EN 17347:2024
Gulf Standard
Current Edition
·
Approved on
31 January 2024
·
Road vehicles - Machines for mounting and demounting vehicle tyres - Safety requirements
GSO EN 17347:2024 Files
English
50 Pages
Current Edition
Reference Language
GSO EN 17347:2024 Scope
This Standard specifies the safety requisites requirements and their verification for the design and building of machines (see the definition in point 3.2) for mounting and demounting tyres on the vehicles listed below and identified according to the international categories M1, M2, N1, O1, O2, L4 and L5:
a) cars
b) buses
c) lorries
d) motor-vehicles for specific or special transport
e) mobile homes
f) cargo trailers
g) car trailers
h) motorised quadricycles
i) motor vehicles
j) mopeds
k) agricultural machines (if the wheel/tyre dimensions are compatible with the maximum dimensions indicated in the tyre changer user instructions)
The vehicles listed in points a) to f) must have an overall full-load mass no greater than 3.5 t.
These machines are designed to ensure the tyre is correctly fitted on the wheel in safe conditions. The standard describes how to eliminate or reduce the risks resulting from the foreseen use (or improper but reasonably foreseeable use) of these machines by the operator during normal operation and service. In addition, it specifies the type of information that the manufacturer must supply with regards to safe working procedures.
The Standard describes all the significant hazards (as listed in Table 1) and the danger situations and events relating to these machines.
This Standard does not apply to hazards regarding maintenance or repairs carried out by professional maintenance personnel.
Best Sellers From Mechanical Sector
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
BH GSO 42:2015
GSO 42:2015
Bahraini Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![BH Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_bh_sml.png)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
BH GSO 159:2015
GSO 159:1993
Bahraini Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![BH Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_bh_sml.png)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ASTM D4778:2024
ASTM D4778:15
Gulf Standard
Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ASTM Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_astm_sml.png)
GSO ISO 11114-6:2024
ISO 11114-6:2022
Gulf Standard
Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 6: Oxygen pressure surge testing
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 23598:2024
ISO 23598:2021
Gulf Standard
Mechanical joining of sheet materials — Destructive testing of joints — Specimen dimensions and procedure for mechanized peel testing of single joints
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 22407:2024
ISO 22407:2021
Gulf Standard
Metallic materials — Fatigue testing — Axial plane bending method
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)