ISO 21138-3:2020

مواصفة قياسية دولية   الإصدار الحالي
اعتمدت بتاريخ  20 يناير 2020

Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B

أنظمة الصرف الصحي الخارجية
* تصريف ومعالجة مياه الصرف الصحي ، انظر 13.060.30 * أنظمة التصريف الداخلي، انظر 91.140.80
أنظمة الصرف الصحي
* معالجة وتصريف مياه الصرف الصحي، انظر 13.060.30 * أنظمة تصريف مياه الأمطار، انظر 91.060.20 * أنظمة تصريف مياه الصرف الصحي الخارجية، انظر 93.030

ملفات الوثيقة ISO 21138-3:2020

الإنجليزية 38 صفحات
الإصدار الحالي
67.36 BHD

مجال الوثيقة ISO 21138-3:2020

This document, together with ISO 21138‑1, specifies the definitions and requirements for pipes with a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications.

NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway drainage and surface water.

This document specifies test methods and test parameters.

This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours.

NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.

In conjunction with ISO 21138‑1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials.

It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.

NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 are deemed to be suitable for use with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in ISO 21138‑2 or ISO 21138‑3 (this document) and to the performance requirements given in Clause 10.

NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

Test methods are not included in this document.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-1:2015
GSO 150-1:2013 
لائحة فنية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية
GSO 150-1:2013
 
لائحة فنية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية

اعتمدت مؤخراً

ISO 6603-2:2023
 
مواصفة قياسية دولية
Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
ISO 23256:2023
 
مواصفة قياسية دولية
Water quality — Detection of selected congeners of polychlorinated dibenzo-p-dioxins and polychlorinated biphenyls — Method using a flow immunosensor technique
ISO/TR 5202:2023
 
مواصفة قياسية دولية
Buildings and civil engineering works — Building resilience strategies related to public health emergencies — Compilation of relevant information
ISO 10605:2023
 
مواصفة قياسية دولية
Road vehicles — Test methods for electrical disturbances from electrostatic discharge