ISO 23856:2021

مواصفة قياسية دولية   الإصدار الحالي

Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

المجال

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.

NOTE 1   For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).

NOTE 2   Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.

NOTE 3   This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.

NOTE 4   ISO 10467 and ISO 10639, which are replaced by this document, are also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.

The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.

This document is applicable to circular pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.

إعداد
15 يونيو 2021
أنظمة الصرف الصحي الخارجية
* تصريف ومعالجة مياه الصرف الصحي ، انظر 13.060.30 * أنظمة التصريف الداخلي، انظر 91.140.80
أنظمة الصرف الصحي
* معالجة وتصريف مياه الصرف الصحي، انظر 13.060.30 * أنظمة تصريف مياه الأمطار، انظر 91.060.20 * أنظمة تصريف مياه الصرف الصحي الخارجية، انظر 93.030

الملفات

null صفحات
الإصدار الحالي
null null
 

المواصفات ذات العلاقة

revises
ISO 10639:2017
 
إصدار سابق
مواصفة قياسية دولية
Plastics piping systems for pressure and non-pressure water supply — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
revises
ISO 10467:2018
 
إصدار سابق
مواصفة قياسية دولية
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

الأكثر مبيعاً

GSO 9:2013
 
لائحة فنية خليجية
بطاقات المواد الغذائية المعبأة
BH GSO 9:2015
GSO 9:2013 
لائحة فنية بحرينية
بطاقات المواد الغذائية المعبأة
GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية

اعتمدت مؤخراً

CLC/TS 50600-5-1:2021
 
مواصفة قياسية دولية
Information technology - Data centre facilities and infrastructures - Part 5-1: Maturity Model for Energy Management and Environmental Sustainability
EN 50491-12-2:2022
 
مواصفة قياسية دولية
General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 12-2: Smart grid - Application specification - Interface and framework for customer - Interface between the Home / Building CEM and Resource manager(s) - Data model and messaging
EN IEC 60947-5-2:2020/A11:2022
 
مواصفة قياسية دولية
Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches
EN IEC 60598-1:2021/A11:2022
 
مواصفة قياسية دولية
Luminaires - Part 1: General requirements and tests