ISO 4981:2023

مواصفة قياسية دولية   الإصدار الحالي
· اعتمدت بتاريخ ٢٧ يونيو ٢٠٢٣ ·

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Boxes used for retention, detention, storage and transportation systems — Specifications for storm water boxes made of PE, PP and PVC-U

الأنظمة الخارجية لنقل الماء
* تشمل التمديدات المدفونة أو على سطح الأرض * التمديدات الداخلية فى المباني ، انظر 91.140.60

ملفات الوثيقة ISO 4981:2023

الإنجليزية 16 صفحات
الإصدار الحالي
42.04 BHD

مجال الوثيقة ISO 4981:2023

This document gives the definitions and specifies the minimum requirements for injection moulded, extruded, compression moulded and thermoformed thermoplastics cuboid shaped boxes, including integral components, used in underground systems for retention, detention, storage and transportation of non-potable water (e.g. storm water) and manufactured from polyethylene (PE), polypropylene (PP) or unplasticized polyvinylchloride (PVC-U).

The boxes are intended for buried underground use, e.g. in landscape, pedestrian or vehicular traffic areas.

In the case of retention and detention systems, the main purpose of the boxes is to retain water, for later infiltration in the ground or for later use in non-potable applications (irrigation, cleaning, sanitary facilities, etc.) or to retain water during a storm, transferring it in a controlled way to the public storm water network.

Applications include commercial, residential, agricultural and highway drainage, including installation under parking lots and roadways.

Product performance is determined by a combination of material specification, product design and manufacturing process.

A box can either be factory-assembled or site-assembled from different components.

The boxes are intended to be used as elements in a modular system where the manufacturer has provided a clearly documented method specifying how the components are assembled to create a complete retention, detention, storage and transportation system. The boxes are installed as one or more horizontal layers on a firm foundation and embedded with fill around and above the complete system.

NOTE       Non-load bearing component(s) can be manufactured by various methods (e.g. extrusion, injection moulding, rotational moulding, compression moulded, thermoforming and low-pressure injection moulding) and are not within the scope of this document.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 2055-1:2016
GSO 2055-1:2015 
لائحة فنية بحرينية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال
GSO 2055-1:2015
 
لائحة فنية خليجية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال

اعتمدت مؤخراً

ISO 10319:2024
 
مواصفة قياسية دولية
Geosynthetics — Wide-width tensile test
ISO 18893:2024
 
مواصفة قياسية دولية
Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
ISO 9842:2024
 
مواصفة قياسية دولية
Essential oil of rose (Rosa x damascena Miller)
ISO 5459:2024
 
مواصفة قياسية دولية
Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems