ISO/IEC Guide 98-6:2021

مواصفة قياسية دولية   الإصدار الحالي
اعتمدت بتاريخ  09 فبراير 2021

Uncertainty of measurement — Part 6: Developing and using measurement models

المترولوجيا والقياس بصفة عامة
* يشمل أدوات القياس بصفة عامة، الأرقام القياسية، المقاييس المستخدمة، الجوانب العامة للمواد المرجعية ، الخ * الكميات والوحدات، انظر 67.0501.060 * المواد المرجعية الكيميائية، انظر 71.040.30

ملفات الوثيقة ISO/IEC Guide 98-6:2021

null صفحات
الإصدار الحالي

مجال الوثيقة ISO/IEC Guide 98-6:2021

This document provides guidance on developing and using a measurement model and also covers the assessment of the adequacy of a measurement model. The document is of particular interest to developers of measurement procedures, working instructions and documentary standards. The model describes the relationship between the output quantity (the measurand) and the input quantities known to be involved in the measurement. The model is used to obtain a value for the measurand and an associated uncertainty. Measurement models are also used in, for example, design studies, simulation of processes, and in

engineering, research and development.

This document explains how to accommodate in a measurement model the quantities involved. These quantities relate i) to the phenomenon or phenomena on which the measurement is based, that is, the measurement principle, ii) to effects arising in the specific measurement, and iii) to the interaction with the artefact or sample subject to measurement.

The guidance provided is organised in accordance with a work flow that could be contemplated when developing a measurement model from the beginning. This work flow starts with the specification of the measurand (clause 6). Then the measurement principle is modelled (clause 7) and an appropriate form of the model is chosen (clause 8). The basic model thus obtained is extended by identifying (clause 9) and adding (clause 10) effects arising from the measurement and the artefact or sample subject to measurement. Guidance on assessing the adequacy of the resulting measurement model is given in clause 12. The distinction between the basic model and the (complete) measurement model in the work flow should be helpful to those readers who already have a substantial part of the measurement model in place, but would like to verify that it contains all effects arising from the measurement so that it is fit for purpose.

Guidance on the assignment of probability distributions to the quantities appearing in the measurement model is given in JCGM 100:2008 and JCGM 101:2008. In clause 11, this guidance is supplemented by describing how statistical models can be developed and used for this purpose.

When using a measurement model, numerical problems can arise including computational effects such as rounding and numerical overflow. It is demonstrated how such problems can often be alleviated by expressing a model differently so that it performs well in calculations. It is also shown how a reformulation of the model can sometimes be used to eliminate some correlation effects among the input quantities when such dependencies exist.

Examples from a number of metrology disciplines illustrate the guidance provided in this document.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-1:2015
GSO 150-1:2013 
لائحة فنية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية
GSO 150-1:2013
 
لائحة فنية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية

اعتمدت مؤخراً

ISO 15500-13:2023
 
مواصفة قياسية دولية
Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD)
ISO/TS 11007-2:2023
 
مواصفة قياسية دولية
Petroleum products and lubricants — Determination of rust-prevention characteristics of lubricating greases — Part 2: Method with water wash-out
ISO 13583-2:2023
 
مواصفة قياسية دولية
Centrifugally cast steel and alloy products — Part 2: Heat-resistant materials
ISO 7784-1:2023
 
مواصفة قياسية دولية
Paints and varnishes — Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen