ISO 6507-1:2023

مواصفة قياسية دولية   الإصدار الحالي · اعتمدت بتاريخ ١٦ أكتوبر ٢٠٢٣

Metallic materials — Vickers hardness test — Part 1: Test method

ملفات الوثيقة ISO 6507-1:2023

الإنجليزية 35 صفحات
الإصدار الحالي
63.65 BHD

مجال الوثيقة ISO 6507-1:2023

This document specifies the Vickers hardness test method for the three different ranges of test force for metallic materials, including hard metals and other cemented carbides (see Table 1), metallic coatings and other inorganic coatings.

The Vickers hardness test is specified in this document for lengths of indentation diagonals between 0,020 mm and 1,400 mm. Using this method to determine Vickers hardness from smaller indentations is outside the scope of this document as results would suffer from large uncertainties due to the limitations of optical measurement and imperfections in tip geometry.

The Vickers hardness specified in this document is also applicable for metallic and other inorganic coatings including electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic coatings on aluminium.

This document is applicable to measurements normal to the coated surface and to measurements on cross-sections, provided that the characteristics of the coating (smoothness, thickness, etc.) permit accurate readings of the diagonal of the indentation.

This document is not applicable for coatings with thickness less than 0,030 mm when testing normal to the coating surface. This standard is not applicable for coatings with thickness less than 0,100 mm when testing a cross-section of the coating. ISO 14577-1 can be used for the determination of hardness from smaller indentations.”

A periodic verification method is specified for routine checking of the testing machine in service by the user.

For specific materials and/or products, relevant International Standards exist.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 2055-1:2016
GSO 2055-1:2015 
لائحة فنية بحرينية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال
GSO 2055-1:2015
 
لائحة فنية خليجية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال

اعتمدت مؤخراً

ISO/PAS 8800:2024
 
مواصفة قياسية دولية
Road vehicles — Safety and artificial intelligence
ISO 19880-8:2024
 
مواصفة قياسية دولية
Gaseous hydrogen — Fuelling stations — Part 8: Fuel quality control
ISO/TR 27926:2024
 
مواصفة قياسية دولية
Carbon dioxide capture, transportation and geological storage — Carbon dioxide enhanced oil recovery (CO2-EOR) — Transitioning from EOR to storage
ISO/IEC 19566-10:2024
 
مواصفة قياسية دولية
Information technology — JPEG Systems — Part 10: Reference software