ISO 21105-1:2019

مواصفة قياسية دولية   الإصدار الحالي · اعتمدت بتاريخ ١٤ نوفمبر ٢٠١٩

Performance of buildings — Building enclosure thermal performance verification and commissioning — Part 1: General requirements

ملفات الوثيقة ISO 21105-1:2019

الإنجليزية 27 صفحات
الإصدار الحالي
71.13 BHD

مجال الوثيقة ISO 21105-1:2019

This document describes a building enclosure commissioning process to achieve a well performing, durable and maintainable building enclosure. This document includes procedures, methods and documentation requirements describing the application of the commissioning process to a building enclosure at each phase of a project. These project phases span from predesign through owner occupancy and operation. This process is referred to throughout this document as building enclosure commissioning (BECx).

This document applies to new building construction and building re-commissioning. This document is for use by an owner, commissioning provider, building developer, owner's representative, construction manager, architect, contractor, and/or consultant, etc. Its purpose is to determine and complete the required tasks and activities to deliver a building enclosure which meets the performance requirements of the owner. Requirements for the project are established by the owner and/or commissioning provider (CxP).

This document identifies steps necessary to perform a building enclosure risk analysis. The analysis will result in tasks that define the level of BECx, commensurate with the owner's tolerance for risk associated with building enclosure performance.

The BECx process covered by this document is applicable to an individual assembly, a combination of assemblies or a whole enclosure assembly. For example, an individual assembly can be the fenestration, the air barrier or the thermal insulation. A combination of assemblies would include the fenestration, the air barrier and the complete heat transfer system, (e.g. both the insulation and roof assembly). A whole building enclosure assembly would include all heat, air and moisture control layers of the building enclosure, on all six sides of the building.

This document describes requirements for any third-party consultants and/or building enclosure commissioning providers (BECxP) to document their technical qualifications, independence and knowledge of the BECx process, including their education, training, and experience.

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 2055-1:2016
GSO 2055-1:2015 
لائحة فنية بحرينية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال
GSO 2055-1:2015
 
لائحة فنية خليجية
الأغذية الحلال – الجزء الأول : الاشتراطات العامة للأغذية الحلال

اعتمدت مؤخراً

ISO/TR 4752:2025
 
مواصفة قياسية دولية
Biotechnology — Inventory of methods for detection of microbiological contamination in mammalian cell culture
ISO 21043-3:2025
 
مواصفة قياسية دولية
Forensic sciences — Part 3: Analysis
ISO 19984-2:2025
 
مواصفة قياسية دولية
Rubber and rubber products — Determination of biobased content — Part 2: Biobased carbon content
ISO/TS 6417:2025
 
مواصفة قياسية دولية
Microfluidic pumps — Symbols and performance communication