ISO 16422-1:2024

مواصفة قياسية دولية   الإصدار الحالي
· اعتمدت بتاريخ 01 فبراير 2024 ·

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General

ملفات الوثيقة ISO 16422-1:2024

null صفحات
الإصدار الحالي

مجال الوثيقة ISO 16422-1:2024

This document specifies the general characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or above-ground (where protected from direct sunlight), for water supply, buried drainage, sewerage, treated waste water and irrigation under pressure.

In conjunction with ISO 16422-2, ISO/TS 16422-3, ISO 16422-5 and ISO 1452-4, this document is applicable to PVC-O pipes and PVC-O fittings, as well as to valves, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:

a)       water mains and services lines;

b)       conveyance of water for both outside and inside buildings;

c)        drainage, sewerage and treated wastewater under pressure;

d)       irrigation under pressure.

This document is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for wastewater under pressure.

This document is also applicable to components for the conveyance of water and wastewater up to and including 45 °C. For temperatures between 25 °C and 45 °C, see ISO 16422-2:2023, Figure C.1.

The piping system according to this document is intended for the conveyance of cold water up to pressures of 25 bar[1] and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bar.

[1]  1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2

الأكثر مبيعاً

GSO 150-2:2013
 
مواصفة قياسية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-2:2015
GSO 150-2:2013 
مواصفة قياسية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الثاني : فترات الصلاحية الاختيارية
BH GSO 150-1:2015
GSO 150-1:2013 
لائحة فنية بحرينية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية
GSO 150-1:2013
 
لائحة فنية خليجية
فترات صلاحية المنتجات الغذائية - الجزء الأول : فترات الصلاحية الإلزامية

اعتمدت مؤخراً

ISO/IEC 14763-3:2024
 
مواصفة قياسية دولية
Information technology — Implementation and operation of customer premises cabling — Part 3: Testing of optical fibre cabling
ISO 12625-5:2024
 
مواصفة قياسية دولية
Tissue paper and tissue products — Part 5: Determination of wet tensile strength
ISO 11772:2024
 
مواصفة قياسية دولية
Hot-rolled longitudinally profiled steel plate
ISO 24146-1:2024
 
مواصفة قياسية دولية
Ships and marine technology — Shipboard waste on inland navigation vessels — Part 1: On board management and handling