IEC 80601-2-58:2024

International Standard   Current Edition
· Approved on 08 March 2024 ·

Medical electrical equipment — Part 2-58: Particular requirements for basic safety and essential performance of lens removal devices and vitrectomy devices for ophthalmic surgery

Ophthalmic equipment
Including ophthalmic implants, glasses, contact lenses and their cleaning products

IEC 80601-2-58:2024 Files

null Pages
Current Edition

IEC 80601-2-58:2024 Scope

This document applies to the BASIC SAFETY and ESSENTIAL PERFORMANCE of LENS REMOVAL DEVICES and VITRECTOMY DEVICES for ophthalmic surgery (as defined in 201.3.209 and 201.3.217) and associated ACCESSORIES that can be connected to this MEDICAL ELECTRICAL EQUIPMENT, hereafter referred to as ME EQUIPMENT. If a clause or subclause is specifically intended to be applicable to ME EQUIPMENT only, or to ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant. HAZARDS inherent in the intended physiological function of ME EQUIPMENT or ME SYSTEMS within the scope of this document are not covered by specific requirements in this document except in 7.2.13 of IEC 60601-1:2005 and IEC 60601 1:2005/AMD2:2020 and 8.4.1 of IEC 60601-1:2005. IEC 80601-2-58:2024 cancels and replaces the second edition published in 2014 and its Amendment 1:2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:

a) the alignment of this particular standard based on the amendment of IEC 60601-1:2005, IEC 60601-1:2005/AMD1:2012 and IEC 60601-1:2005/AMD2:2020;

b) updating collateral, particular and IEC 60601-1:2005, IEC 60601-1:2005/AMD1:2012 and IEC 60601-1:2005/AMD2:2020 references to align with amendments to IEC 60601-1:2005, IEC 60601-1:2005/AMD1:2012 and IEC 60601-1:2005/AMD2:2020 and other collateral standards;

c) updated normative references;

d) added new requirement for particulate matter from APPLIED PARTS in 201.9.5.101;

e) adding the shadow light method in 201.12.1.101.7;

f) clarify test conditions for EMC requirements in 202.7.1.2;

g) updated Table D.4 references to include specific IEC references to the symbols and delete “Annex AA, 201.7.6.101”;

h) include a new annex to address the relevant general safety and performance requirements of European regulation (EU) 2017/745 (Annex BB);

i) remove all references of the LIQUEFACTION FRAGMENTATION LENS REMOVAL method.

Best Sellers

GSO 150-2:2013
 
Gulf Standard
Expiration dates for food products - Part 2 : Voluntary expiration dates
BH GSO 150-2:2015
GSO 150-2:2013 
Bahraini Standard
Expiration dates for food products - Part 2 : Voluntary expiration dates
BH GSO 150-1:2015
GSO 150-1:2013 
Bahraini Technical Regulation
Expiration dates for food products -Part 1 : Mandatory expiration dates
GSO 150-1:2013
 
Gulf Technical Regulation
Expiration dates for food products -Part 1 : Mandatory expiration dates

Recently Published

ISO 17099:2024
 
International Standard
Radiological protection — Performance criteria for laboratories using the cytokinesis-block micronucleus (CBMN) assay in peripheral blood lymphocytes for biological dosimetry
ISO 23555-3:2024
 
International Standard
Gas pressure safety and control devices for use in gas transmission, distribution and installations for inlet pressures up to and including 10 MPa — Part 3: Safety shut-off devices
ISO/TS 9321:2024
 
International Standard
Health informatics — General requirements of multi-centre medical data collaborative analysis
ISO 4080:2024
 
International Standard
Rubber and plastics hoses and tubing, and their assemblies — Determination of permeability to gas